APRS Track Direct

My position About ☰

reset

HS2AB-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS2AB-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TxTraffic*	RSSI*	Voltage*
1790664597	0 Pkt	-40 dBm	4.04 V
1790663387	0 Pkt	-42 dBm	3.63 V
1790662177	0 Pkt	-41 dBm	3.4 V
1790660967	0 Pkt	-40 dBm	2.83 V
1790659757	0 Pkt	-43 dBm	2.63 V
1790658547	1 Pkt	-41 dBm	2.5 V
1790657337	0 Pkt	-40 dBm	2.54 V
1790656127	0 Pkt	-43 dBm	2.15 V
1790654917	0 Pkt	-40 dBm	2.01 V
1790653707	0 Pkt	-40 dBm	2.05 V
1790652497	0 Pkt	-43 dBm	1.91 V
1790651287	0 Pkt	-41 dBm	2.09 V
1790650077	0 Pkt	-40 dBm	2.4 V
1790648867	0 Pkt	-41 dBm	2.4 V
1790647657	0 Pkt	-39 dBm	2.11 V
1790646447	0 Pkt	-40 dBm	2.42 V
1790645237	0 Pkt	-39 dBm	1.15 V
1790644027	0 Pkt	-40 dBm	1.15 V
1790642817	0 Pkt	-40 dBm	1.39 V
1790641607	0 Pkt	-41 dBm	1.03 V
1790640397	0 Pkt	-41 dBm	0.92 V
1790639187	0 Pkt	-38 dBm	0.74 V
1790637977	0 Pkt	-39 dBm	0.53 V
1790636767	0 Pkt	-40 dBm	0.14 V
1790635557	0 Pkt	-39 dBm	0.06 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)