APRS Track Direct

My position About ☰

reset

IR3EO-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IR3EO-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Rx10m*	Rx1h*	Dg10m*
1745034797	162 Pkt	1050 Pkt	151 Pkt
1745034497	152 Pkt	1070 Pkt	151 Pkt
1745034197	148 Pkt	1080 Pkt	151 Pkt
1745033897	169 Pkt	1080 Pkt	151 Pkt
1745033597	176 Pkt	1060 Pkt	151 Pkt
1745033297	155 Pkt	1060 Pkt	151 Pkt
1745032997	155 Pkt	1050 Pkt	152 Pkt
1745032697	152 Pkt	1060 Pkt	151 Pkt
1745032397	163 Pkt	1090 Pkt	151 Pkt
1745032097	155 Pkt	1080 Pkt	152 Pkt
1745031797	158 Pkt	1090 Pkt	151 Pkt
1745031497	183 Pkt	1110 Pkt	151 Pkt
1745031197	188 Pkt	1100 Pkt	151 Pkt
1745030897	154 Pkt	1070 Pkt	151 Pkt
1745030597	149 Pkt	1090 Pkt	152 Pkt
1745030297	159 Pkt	1090 Pkt	151 Pkt
1745029997	160 Pkt	1100 Pkt	152 Pkt
1745029697	175 Pkt	1100 Pkt	151 Pkt
1745029397	186 Pkt	1090 Pkt	151 Pkt
1745029097	169 Pkt	1080 Pkt	151 Pkt
1745028797	172 Pkt	1060 Pkt	151 Pkt
1745028497	176 Pkt	1050 Pkt	151 Pkt
1745028197	161 Pkt	1030 Pkt	151 Pkt
1745027897	161 Pkt	1030 Pkt	152 Pkt
1745027597	164 Pkt	1020 Pkt	151 Pkt

*Used Equation Coefficients:

Rx10m: 0, 1, 0

Rx1h: 0, 10, 0

Dg10m: 0, 1, 0

DgR: 0, 0.001, 0

Eff1h: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)