APRS Track Direct

My position About ☰

reset

YM3KB-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YM3KB-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	TxTraffic*	RSSI*	Voltage*
1786737889	0 Pkt	-38 dBm	12 V
1786734267	0 Pkt	-37 dBm	12 V
1786730645	1 Pkt	-37 dBm	12 V
1786727023	1 Pkt	-37 dBm	12 V
1786723401	2 Pkt	-37 dBm	12 V
1786719779	0 Pkt	-37 dBm	12 V
1786716156	0 Pkt	-37 dBm	12 V
1786712535	0 Pkt	-36 dBm	12 V
1786708913	1 Pkt	-36 dBm	12 V
1786705290	1 Pkt	-37 dBm	12 V
1786701668	15 Pkt	-37 dBm	12 V
1786698046	0 Pkt	-37 dBm	12 V
1786694424	1 Pkt	-37 dBm	12 V
1786690802	0 Pkt	-37 dBm	12 V
1786687181	2 Pkt	-37 dBm	12 V
1786683558	0 Pkt	-37 dBm	12 V
1786679936	10 Pkt	-37 dBm	12 V
1786676314	0 Pkt	-37 dBm	12 V
1786672692	0 Pkt	-37 dBm	12 V
1786669070	1 Pkt	-36 dBm	12 V
1786665448	1 Pkt	-37 dBm	12 V
1786661826	0 Pkt	-37 dBm	12 V
1786658204	0 Pkt	-37 dBm	12 V
1786654582	0 Pkt	-37 dBm	12 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)