APRS Track Direct

My position About ☰

reset

SQ8MAE-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ8MAE-5. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Eff*
1754127297	13.2 Volt	100 Pcnt	83 Pcnt
1754126696	13.2 Volt	100 Pcnt	83 Pcnt
1754126096	13.2 Volt	100 Pcnt	83 Pcnt
1754125495	13.2 Volt	100 Pcnt	83 Pcnt
1754124894	13.2 Volt	100 Pcnt	83 Pcnt
1754124294	13.2 Volt	100 Pcnt	83 Pcnt
1754123693	13.2 Volt	100 Pcnt	83 Pcnt
1754123093	13.2 Volt	100 Pcnt	83 Pcnt
1754122492	13.2 Volt	100 Pcnt	83 Pcnt
1754121892	13.2 Volt	100 Pcnt	83 Pcnt
1754121291	13.2 Volt	100 Pcnt	83 Pcnt
1754120690	13.2 Volt	100 Pcnt	83 Pcnt
1754120090	13.2 Volt	100 Pcnt	83 Pcnt
1754119489	13.2 Volt	100 Pcnt	83 Pcnt
1754118889	13.2 Volt	100 Pcnt	83 Pcnt
1754118288	13.2 Volt	100 Pcnt	83 Pcnt
1754117688	13.2 Volt	100 Pcnt	83 Pcnt
1754117087	13.2 Volt	100 Pcnt	83 Pcnt
1754116487	13.2 Volt	100 Pcnt	83 Pcnt
1754115886	13.2 Volt	100 Pcnt	83 Pcnt
1754115285	13.2 Volt	100 Pcnt	83 Pcnt
1754114685	13.2 Volt	100 Pcnt	83 Pcnt
1754114084	13.2 Volt	100 Pcnt	83 Pcnt
1754113484	13.2 Volt	100 Pcnt	83 Pcnt
1754112883	13.2 Volt	100 Pcnt	83 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx10m: 0, 1, 0

Rx1h: 0, 10, 0

Eff1h: 0, 1, 0

Eff: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)