APRS Track Direct

My position About ☰

reset

TB3ACE-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TB3ACE-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	DIGI*	CONN*	VBAT*
1790650551	120 pkt	60 pkt	55 pkt	1 cnt	0.52 V
1790649831	115 pkt	58 pkt	53 pkt	1 cnt	0.52 V
1790649111	110 pkt	56 pkt	51 pkt	1 cnt	0.52 V
1790648391	105 pkt	54 pkt	49 pkt	1 cnt	0.51 V
1790647671	100 pkt	52 pkt	47 pkt	1 cnt	0.52 V
1790646951	95 pkt	50 pkt	45 pkt	1 cnt	0.52 V
1790646231	86 pkt	43 pkt	39 pkt	1 cnt	0.52 V
1790645511	81 pkt	41 pkt	37 pkt	1 cnt	0.51 V
1790644790	76 pkt	38 pkt	35 pkt	1 cnt	0.52 V
1790644070	71 pkt	36 pkt	33 pkt	1 cnt	0.5 V
1790643350	66 pkt	34 pkt	31 pkt	1 cnt	0.52 V
1790642630	61 pkt	32 pkt	29 pkt	1 cnt	0.5 V
1790641910	53 pkt	27 pkt	24 pkt	1 cnt	0.53 V
1790641190	48 pkt	25 pkt	22 pkt	1 cnt	0.52 V
1790640470	42 pkt	22 pkt	19 pkt	1 cnt	0.51 V
1790639750	37 pkt	20 pkt	17 pkt	1 cnt	0.49 V
1790639030	32 pkt	17 pkt	15 pkt	1 cnt	0.52 V
1790638310	27 pkt	15 pkt	13 pkt	1 cnt	0.51 V
1790637590	21 pkt	12 pkt	10 pkt	1 cnt	0.51 V
1790636870	15 pkt	9 pkt	7 pkt	1 cnt	0.51 V
1790636150	8 pkt	4 pkt	3 pkt	1 cnt	0.51 V
1790635430	2 pkt	0 pkt	0 pkt	1 cnt	0.48 V
1790634706	161 pkt	83 pkt	72 pkt	1 cnt	0.51 V
1790633986	155 pkt	78 pkt	69 pkt	1 cnt	0.51 V
1790633266	149 pkt	74 pkt	66 pkt	1 cnt	0.51 V

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

DIGI: 0, 1, 0

CONN: 0, 1, 0

VBAT: 0, 0.01, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)