APRS Track Direct

My position About ☰

reset

XE3JAC-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object XE3JAC-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	TxTraffic*	RSSI*	Voltage*
1836274418	0 Pkt	0 Pkt	-63 dBm	21 V
1836274246	0 Pkt	0 Pkt	-62 dBm	21 V
1766235957	0 Pkt	0 Pkt	-60 dBm	21 V
1766235035	0 Pkt	0 Pkt	-61 dBm	21 V
1766234113	0 Pkt	0 Pkt	-61 dBm	21 V
1766233191	0 Pkt	0 Pkt	-62 dBm	21 V
1766232269	0 Pkt	0 Pkt	-61 dBm	21 V
1766231347	0 Pkt	0 Pkt	-62 dBm	21 V
1766230426	0 Pkt	0 Pkt	-61 dBm	21 V
1766229503	0 Pkt	0 Pkt	-62 dBm	21 V
1766228581	0 Pkt	0 Pkt	-62 dBm	21 V
1766227659	0 Pkt	0 Pkt	-62 dBm	21 V
1766227120	0 Pkt	1 Pkt	-61 dBm	21 V
1766226198	0 Pkt	3 Pkt	-62 dBm	21 V
1766225276	0 Pkt	2 Pkt	-61 dBm	21 V
1766224354	0 Pkt	2 Pkt	-63 dBm	21 V
1766223432	1 Pkt	2 Pkt	-61 dBm	21 V
1766222509	0 Pkt	0 Pkt	-64 dBm	21 V
1766221587	0 Pkt	4 Pkt	-61 dBm	21 V
1766220665	0 Pkt	2 Pkt	-62 dBm	21 V
1766219743	0 Pkt	2 Pkt	-61 dBm	21 V
1766218822	0 Pkt	3 Pkt	-63 dBm	21 V
1766217899	0 Pkt	1 Pkt	-61 dBm	21 V
1766216978	0 Pkt	3 Pkt	-62 dBm	21 V
1766216055	0 Pkt	2 Pkt	-61 dBm	21 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)