APRS Track Direct

My position About ☰

reset

HS6PAU-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS6PAU-12. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1790597849	0 Pkt	-59 dBm	20.26 V
1790597526	0 Pkt	-61 dBm	20.61 V
1790597202	0 Pkt	-58 dBm	20.69 V
1790596878	0 Pkt	-59 dBm	20.69 V
1790596554	0 Pkt	-56 dBm	20.59 V
1790596230	0 Pkt	-61 dBm	20.67 V
1790595906	0 Pkt	-58 dBm	20.77 V
1790595582	0 Pkt	-59 dBm	0.21 V
1790595258	0 Pkt	-59 dBm	0.18 V
1790594934	0 Pkt	-58 dBm	0.18 V
1790594610	0 Pkt	-59 dBm	0.18 V
1790594286	0 Pkt	-58 dBm	0.21 V
1790593962	0 Pkt	-58 dBm	0.25 V
1790593638	0 Pkt	-58 dBm	0.39 V
1790593315	0 Pkt	-58 dBm	0.59 V
1790592991	1 Pkt	-61 dBm	0.98 V
1790592667	0 Pkt	-60 dBm	1.27 V
1790592343	0 Pkt	-58 dBm	1.39 V
1790592019	0 Pkt	-60 dBm	2.03 V
1790591695	1 Pkt	-59 dBm	2.77 V
1790591371	0 Pkt	-59 dBm	3.24 V
1790591047	2 Pkt	-59 dBm	3.49 V
1790590723	0 Pkt	-58 dBm	3.53 V
1790590399	0 Pkt	-61 dBm	3.28 V
1790590075	0 Pkt	-59 dBm	3.49 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)