APRS Track Direct

My position About ☰

reset

9A1W-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 9A1W-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Temp I*	Rx1h*	Dg1h*
1732288679	14.03 Volt	0.5 C	1310 Pkt	260 Pkt
1732288380	14.03 Volt	0.5 C	1300 Pkt	260 Pkt
1732288379	14.03 Volt	0.5 C	1300 Pkt	260 Pkt
1732288079	14.03 Volt	0.5 C	1320 Pkt	270 Pkt
1732287780	14.03 Volt	0.5 C	1310 Pkt	270 Pkt
1732287779	14.03 Volt	0.5 C	1310 Pkt	270 Pkt
1732287479	13.95 Volt	0.5 C	1300 Pkt	270 Pkt
1732287182	14.03 Volt	0.5 C	1320 Pkt	270 Pkt
1732287179	14.03 Volt	0.5 C	1320 Pkt	270 Pkt
1732286880	14.03 Volt	0.5 C	1340 Pkt	270 Pkt
1732286581	14.03 Volt	0.5 C	1320 Pkt	280 Pkt
1732286580	14.03 Volt	0.5 C	1320 Pkt	280 Pkt
1732286280	14.03 Volt	0.5 C	1310 Pkt	270 Pkt
1732285982	14.03 Volt	0.5 C	1270 Pkt	260 Pkt
1732285980	14.03 Volt	0.5 C	1270 Pkt	260 Pkt
1732285679	14.03 Volt	0.5 C	1250 Pkt	250 Pkt
1732285380	14.03 Volt	0.5 C	1260 Pkt	250 Pkt
1732285379	14.03 Volt	0.5 C	1260 Pkt	250 Pkt
1732285079	14.03 Volt	0.5 C	1230 Pkt	240 Pkt
1732284781	14.03 Volt	0.5 C	1170 Pkt	230 Pkt
1732284779	14.03 Volt	0.5 C	1170 Pkt	230 Pkt
1732284479	14.03 Volt	0.5 C	1160 Pkt	220 Pkt
1732284183	14.03 Volt	0.5 C	1120 Pkt	210 Pkt
1732284180	14.03 Volt	0.5 C	1120 Pkt	210 Pkt
1732283880	14.03 Volt	0.5 C	1070 Pkt	200 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

V AC: 0, 0.075, 0

Temp I: 0, 0.5, -64

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)