APRS Track Direct

My position About ☰

reset

YB8VK-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YB8VK-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1754512605	0 Pkt	-83 dBm	0.37 V
1754512283	0 Pkt	-83 dBm	0.88 V
1754511961	0 Pkt	-82 dBm	0.43 V
1754511639	0 Pkt	-83 dBm	0.57 V
1754511317	0 Pkt	-82 dBm	0.02 V
1754510995	0 Pkt	-83 dBm	0.31 V
1754510673	0 Pkt	-84 dBm	0.06 V
1754510351	1 Pkt	-83 dBm	0.35 V
1754510029	0 Pkt	-82 dBm	0.08 V
1754509706	0 Pkt	-83 dBm	0.51 V
1754509384	0 Pkt	-83 dBm	0.27 V
1754509062	0 Pkt	-83 dBm	0.33 V
1754508740	0 Pkt	-82 dBm	0.04 V
1754508418	0 Pkt	-83 dBm	0.14 V
1754508096	0 Pkt	-83 dBm	0.41 V
1754507774	0 Pkt	-81 dBm	0.25 V
1754507452	0 Pkt	-83 dBm	0.84 V
1754507141	0 Pkt	-82 dBm	0.04 V
1754506808	0 Pkt	-82 dBm	0.33 V
1754506486	0 Pkt	-82 dBm	0.51 V
1754506164	0 Pkt	-82 dBm	0.88 V
1754505843	0 Pkt	-82 dBm	0.49 V
1754505520	0 Pkt	-83 dBm	0.37 V
1754505198	0 Pkt	-82 dBm	0.78 V
1754504876	0 Pkt	-83 dBm	0.49 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)