APRS Track Direct

My position About ☰

reset

YD6HMM-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YD6HMM-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1790637832	6 Pkt	-51 dBm	0.18 V
1790637203	0 Pkt	-46 dBm	0.18 V
1790636579	1 Pkt	-40 dBm	0.18 V
1790635953	0 Pkt	-44 dBm	0.21 V
1790635328	0 Pkt	-46 dBm	0.16 V
1790634703	1 Pkt	-45 dBm	0.18 V
1790634073	0 Pkt	-53 dBm	0.18 V
1790633445	0 Pkt	-48 dBm	0.18 V
1790632820	0 Pkt	-51 dBm	0.18 V
1790632195	1 Pkt	-49 dBm	0.14 V
1790631570	0 Pkt	-42 dBm	0.25 V
1790630945	0 Pkt	-42 dBm	0.21 V
1790630321	0 Pkt	-42 dBm	0.18 V
1790629696	0 Pkt	-42 dBm	0.18 V
1790629072	0 Pkt	-42 dBm	0.18 V
1790628448	0 Pkt	-45 dBm	0.18 V
1790627824	0 Pkt	-42 dBm	0.21 V
1790627199	0 Pkt	-41 dBm	0.18 V
1790626574	2 Pkt	-41 dBm	0.18 V
1790625947	0 Pkt	-43 dBm	0.18 V
1790625322	0 Pkt	-43 dBm	0.21 V
1790624697	0 Pkt	-43 dBm	0.21 V
1790624072	1 Pkt	-41 dBm	0.18 V
1790623447	3 Pkt	-41 dBm	0.21 V
1790622820	0 Pkt	-43 dBm	0.14 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)