APRS Track Direct

My position About ☰

reset

NE1CU-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object NE1CU-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Temp*	Rx1h*	Dg1h*
1762326586	13.58 Volt	64.1 DegF	360 Pkt	120 Pkt
1762325686	13.5 Volt	65 DegF	340 Pkt	120 Pkt
1762324786	13.5 Volt	65 DegF	300 Pkt	120 Pkt
1762323886	13.43 Volt	65 DegF	280 Pkt	120 Pkt
1762322986	13.43 Volt	65 DegF	260 Pkt	110 Pkt
1762322086	13.58 Volt	65 DegF	250 Pkt	100 Pkt
1762321186	13.58 Volt	65 DegF	250 Pkt	100 Pkt
1762320286	13.58 Volt	65 DegF	260 Pkt	100 Pkt
1762319386	13.58 Volt	65.9 DegF	260 Pkt	100 Pkt
1762318486	14.25 Volt	65.9 DegF	250 Pkt	100 Pkt
1762317586	13.88 Volt	65.9 DegF	270 Pkt	110 Pkt
1762316686	13.13 Volt	65.9 DegF	270 Pkt	120 Pkt
1762315786	13.58 Volt	65.9 DegF	250 Pkt	120 Pkt
1762314887	13.8 Volt	65.9 DegF	270 Pkt	120 Pkt
1762313987	12.9 Volt	66.8 DegF	260 Pkt	110 Pkt
1762313087	12.9 Volt	66.8 DegF	270 Pkt	110 Pkt
1762312187	12.23 Volt	66.8 DegF	290 Pkt	100 Pkt
1762311287	12.9 Volt	66.8 DegF	290 Pkt	110 Pkt
1762310387	12.9 Volt	66.8 DegF	280 Pkt	110 Pkt
1762309487	12.9 Volt	66.8 DegF	270 Pkt	110 Pkt
1762308587	12.9 Volt	66.8 DegF	280 Pkt	110 Pkt
1762307687	12.98 Volt	67.7 DegF	270 Pkt	100 Pkt
1762306787	12.98 Volt	67.7 DegF	260 Pkt	90 Pkt
1762305887	12.98 Volt	67.7 DegF	270 Pkt	110 Pkt
1762304987	12.98 Volt	67.7 DegF	270 Pkt	110 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Temp: 0, 0.9, -97

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)