APRS Track Direct

My position About ☰

reset

OE5XDO-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE5XDO-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TEMP-PA*	LM75*	Pv*	Pr*
1753712886	32 Grad	19 Grad	18 W	1.1 W
1753712496	33 Grad	19 Grad	18 W	1.1 W
1753712107	34 Grad	19 Grad	18 W	1.1 W
1753711717	34 Grad	19 Grad	18 W	1 W
1753711328	34 Grad	20 Grad	18 W	1 W
1753710549	34 Grad	20 Grad	18 W	1 W
1753710159	35 Grad	20 Grad	18 W	1 W
1753709770	33 Grad	20 Grad	18 W	1.1 W
1753709380	33 Grad	21 Grad	18 W	1 W
1753708991	33 Grad	21 Grad	18 W	1 W
1753708601	34 Grad	21 Grad	18 W	1 W
1753708214	34 Grad	21 Grad	18 W	1 W
1753707822	34 Grad	21 Grad	18 W	1 W
1753707433	33 Grad	21 Grad	18 W	1 W
1753707043	33 Grad	21 Grad	18 W	1 W
1753706654	33 Grad	21 Grad	18 W	1 W
1753706264	33 Grad	21 Grad	18 W	1 W
1753705875	33 Grad	21 Grad	18 W	1 W
1753705485	32 Grad	21 Grad	18 W	1 W
1753705096	32 Grad	21 Grad	18 W	1 W
1753704706	32 Grad	21 Grad	18 W	1 W
1753704317	33 Grad	20 Grad	18 W	1 W
1753703927	32 Grad	20 Grad	18.3 W	1 W
1753703148	32 Grad	20 Grad	18.3 W	1 W
1753702759	32 Grad	20 Grad	18.3 W	1 W

*Used Equation Coefficients:

TEMP-PA: 0, 1, -150

DACFAN: 0, 1, 0

LM75: 0, 1, -150

Pv: 0, 0.1, 0

Pr: 0, 0.1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)