APRS Track Direct

My position About ☰

reset

G4BDW-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object G4BDW-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	DigiRpt*	Temp*
1749326823	73 Pkts	71 Pkts	48 Pkts	25 C
1749323223	66 Pkts	64 Pkts	46 Pkts	25 C
1749319623	83 Pkts	81 Pkts	50 Pkts	25 C
1749316023	88 Pkts	87 Pkts	64 Pkts	25 C
1749312423	74 Pkts	73 Pkts	52 Pkts	25 C
1749308823	77 Pkts	76 Pkts	52 Pkts	25 C
1749305224	86 Pkts	84 Pkts	55 Pkts	26 C
1749301624	62 Pkts	60 Pkts	45 Pkts	26 C
1749298024	78 Pkts	77 Pkts	52 Pkts	25 C
1749294423	80 Pkts	77 Pkts	55 Pkts	25 C
1749290823	90 Pkts	88 Pkts	48 Pkts	25 C
1749287223	80 Pkts	78 Pkts	44 Pkts	25 C
1749283623	98 Pkts	95 Pkts	57 Pkts	25 C
1749280023	83 Pkts	81 Pkts	46 Pkts	25 C
1749276423	89 Pkts	86 Pkts	50 Pkts	25 C
1749272823	90 Pkts	87 Pkts	52 Pkts	24 C
1749269224	83 Pkts	82 Pkts	52 Pkts	25 C
1749265623	72 Pkts	69 Pkts	47 Pkts	25 C
1749262023	78 Pkts	74 Pkts	47 Pkts	25 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)