APRS Track Direct

My position About ☰

reset

ABAJO Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ABAJO. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1836274678	13.67 Volt	640 Pkt	40 Pkt	68 Pcnt
1836274678	13.67 Volt	640 Pkt	40 Pkt	68 Pcnt
1836274529	13.67 Volt	600 Pkt	40 Pkt	67 Pcnt
1836274528	13.67 Volt	600 Pkt	40 Pkt	67 Pcnt
1836274378	13.67 Volt	640 Pkt	40 Pkt	69 Pcnt
1836274228	13.67 Volt	630 Pkt	40 Pkt	67 Pcnt
1836274079	13.67 Volt	640 Pkt	40 Pkt	68 Pcnt
1836274078	13.67 Volt	640 Pkt	40 Pkt	68 Pcnt
1766207799	13.67 Volt	370 Pkt	10 Pkt	59 Pcnt
1766207500	13.67 Volt	370 Pkt	10 Pkt	59 Pcnt
1766207499	13.67 Volt	370 Pkt	10 Pkt	59 Pcnt
1766207199	13.67 Volt	360 Pkt	10 Pkt	58 Pcnt
1766206900	13.67 Volt	360 Pkt	10 Pkt	57 Pcnt
1766206899	13.67 Volt	360 Pkt	10 Pkt	57 Pcnt
1766206599	13.67 Volt	350 Pkt	10 Pkt	55 Pcnt
1766206300	13.67 Volt	350 Pkt	10 Pkt	55 Pcnt
1766206299	13.67 Volt	350 Pkt	10 Pkt	55 Pcnt
1766205999	13.59 Volt	350 Pkt	10 Pkt	55 Pcnt
1766205700	13.67 Volt	350 Pkt	10 Pkt	56 Pcnt
1766205699	13.67 Volt	350 Pkt	10 Pkt	56 Pcnt
1766205399	13.67 Volt	370 Pkt	10 Pkt	57 Pcnt
1766205100	13.67 Volt	370 Pkt	10 Pkt	57 Pcnt
1766205099	13.67 Volt	370 Pkt	10 Pkt	57 Pcnt
1766204799	13.67 Volt	370 Pkt	10 Pkt	57 Pcnt
1766204500	13.67 Volt	370 Pkt	10 Pkt	57 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)