APRS Track Direct

My position About ☰

reset

9M4CSJ-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 9M4CSJ-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	TxTraffic*	RSSI*	Voltage*
1732471898	0 Pkt	-36 dBm	0 V
1732470073	0 Pkt	-37 dBm	0.02 V
1732468248	0 Pkt	-37 dBm	0.02 V
1732466423	0 Pkt	-35 dBm	0 V
1732463003	0 Pkt	-34 dBm	0 V
1732459583	0 Pkt	-34 dBm	0 V
1732457758	0 Pkt	-40 dBm	0 V
1732455933	3 Pkt	-35 dBm	0.02 V
1732452510	0 Pkt	-34 dBm	0.02 V
1732450685	0 Pkt	-34 dBm	0.02 V
1732447654	0 Pkt	-36 dBm	0 V
1732444623	0 Pkt	-38 dBm	0 V
1732442798	1 Pkt	-37 dBm	0 V
1732440973	0 Pkt	-36 dBm	0 V
1732437553	0 Pkt	-35 dBm	0 V
1732435728	0 Pkt	-37 dBm	0 V
1732432308	3 Pkt	-37 dBm	0 V
1732429277	0 Pkt	-36 dBm	0 V
1732426247	0 Pkt	-40 dBm	0 V
1732423216	0 Pkt	-35 dBm	0 V
1732419796	0 Pkt	-36 dBm	0 V
1732416376	0 Pkt	-35 dBm	0.02 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)