APRS Track Direct

My position About ☰

reset

IR1BY Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IR1BY. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*	Temp*
1836274172	14.33 Volt	790 Pkt	88 Pcnt	16.5 C
1836274020	14.25 Volt	770 Pkt	89 Pcnt	16.5 C
1766219229	14.18 Volt	770 Pkt	80 Pcnt	4.5 C
1766218331	14.18 Volt	720 Pkt	80 Pcnt	5 C
1766217429	14.18 Volt	650 Pkt	79 Pcnt	4.5 C
1766216532	14.18 Volt	660 Pkt	80 Pcnt	5 C
1766215631	14.18 Volt	660 Pkt	80 Pcnt	5 C
1766215629	14.18 Volt	660 Pkt	80 Pcnt	5 C
1766213833	14.18 Volt	640 Pkt	78 Pcnt	4.5 C
1766213829	14.18 Volt	640 Pkt	78 Pcnt	4.5 C
1766212031	14.18 Volt	650 Pkt	80 Pcnt	4 C
1766212029	14.18 Volt	650 Pkt	80 Pcnt	4 C
1766211130	14.18 Volt	680 Pkt	80 Pcnt	4.5 C
1766210233	14.18 Volt	680 Pkt	80 Pcnt	4 C
1766210229	14.18 Volt	680 Pkt	80 Pcnt	4 C
1766209330	14.18 Volt	670 Pkt	80 Pcnt	5 C
1766208429	14.18 Volt	650 Pkt	76 Pcnt	4.5 C
1766206630	14.18 Volt	640 Pkt	77 Pcnt	5 C
1766206629	14.18 Volt	640 Pkt	77 Pcnt	5 C
1766205731	14.18 Volt	670 Pkt	78 Pcnt	4.5 C
1766204830	14.18 Volt	670 Pkt	77 Pcnt	4.5 C
1766204829	14.18 Volt	670 Pkt	77 Pcnt	4.5 C
1766203931	14.18 Volt	660 Pkt	77 Pcnt	4.5 C
1766203030	14.18 Volt	650 Pkt	76 Pcnt	4 C
1766203029	14.18 Volt	650 Pkt	76 Pcnt	4 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)