APRS Track Direct

My position About ☰

reset

BV2CW-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BV2CW-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1790658379	51.4 C	34 p	103 p	3809 p
1790657179	50.9 C	37 p	105 p	3860 p
1790655979	52.3 C	32 p	85 p	3891 p
1790654780	51.1 C	36 p	111 p	3924 p
1790653580	50.8 C	17 p	132 p	3958 p
1790652380	51.4 C	58 p	148 p	4013 p
1790651179	50.4 C	57 p	128 p	4006 p
1790649979	49.9 C	33 p	105 p	4000 p
1790648779	51.6 C	38 p	112 p	4029 p
1790647579	51.2 C	34 p	120 p	4033 p
1790646379	50.3 C	40 p	127 p	4038 p
1790645179	50.8 C	46 p	155 p	4044 p
1790643979	50.5 C	41 p	160 p	4035 p
1790642779	49.9 C	68 p	161 p	4033 p
1790641579	50.6 C	51 p	125 p	4002 p
1790640380	49.9 C	42 p	110 p	3984 p
1790639180	49.9 C	32 p	100 p	3956 p
1790637979	50.5 C	36 p	102 p	3924 p
1790636779	51.4 C	32 p	109 p	3888 p
1790635579	50 C	34 p	110 p	3856 p
1790634380	50.9 C	43 p	92 p	3822 p
1790633180	50.4 C	33 p	91 p	3779 p
1790631979	50.9 C	16 p	99 p	3746 p
1790630779	50.8 C	42 p	120 p	3730 p
1790629579	51 C	41 p	117 p	3688 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)