APRS Track Direct

My position About ☰

reset

HS5TQA-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS5TQA-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	VBAT*	IBAT*	SOLAR*
1790655237	13.77 V	49 mA	23.59 V
1790653436	14.09 V	-89 mA	23.59 V
1790651637	13.86 V	50 mA	23.59 V
1790649837	13.82 V	51 mA	23.59 V
1790648037	13.79 V	-546 mA	23.59 V
1790646237	13.52 V	-543 mA	23.59 V
1790644437	13.38 V	-294 mA	23.59 V
1790642637	13.28 V	-106 mA	23.59 V
1790640837	13.23 V	-17 mA	23.59 V
1790639037	13.22 V	25 mA	23.59 V
1790637237	13.2 V	50 mA	23.59 V
1790635437	13.21 V	46 mA	23.59 V
1790633637	13.2 V	45 mA	23.59 V
1790631837	13.21 V	47 mA	23.59 V
1790630037	13.21 V	55 mA	23.59 V
1790628237	13.21 V	48 mA	23.59 V
1790626437	13.21 V	53 mA	23.59 V
1790624637	13.22 V	47 mA	23.59 V
1790622837	13.22 V	47 mA	23.59 V
1790621037	13.22 V	53 mA	23.59 V
1790619237	13.22 V	49 mA	23.59 V
1790617437	13.22 V	51 mA	23.59 V
1790615637	13.23 V	48 mA	23.59 V
1790613837	13.23 V	53 mA	23.59 V
1790612037	13.23 V	47 mA	23.59 V

*Used Equation Coefficients:

VBAT: 0, 0.01, 0

IBAT: 0, 1, -2000

SOLAR: 0, 0.01, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)