APRS Track Direct

My position About ☰

reset

CT4TX-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object CT4TX-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1732478084	112 Pkt	-57 dBm	8.22 V
1732474421	5 Pkt	-58 dBm	8.24 V
1732472918	141 Pkt	-54 dBm	8.2 V
1732471089	128 Pkt	-56 dBm	8.2 V
1732468402	3 Pkt	-58 dBm	8.2 V
1732467219	115 Pkt	-59 dBm	8.2 V
1732465389	129 Pkt	-60 dBm	8.24 V
1732463557	7 Pkt	-59 dBm	8.2 V
1732463061	122 Pkt	-59 dBm	8.2 V
1732461231	120 Pkt	-58 dBm	8.2 V
1732459400	2 Pkt	-58 dBm	8.22 V
1732458760	141 Pkt	-60 dBm	8.24 V
1732456930	148 Pkt	-60 dBm	8.22 V
1732455098	5 Pkt	-61 dBm	8.24 V
1732453191	121 Pkt	-64 dBm	8.2 V
1732451360	123 Pkt	-58 dBm	8.22 V
1732449530	128 Pkt	-54 dBm	8.24 V
1732447700	125 Pkt	-56 dBm	8.24 V
1732445871	117 Pkt	-55 dBm	8.24 V
1732444041	117 Pkt	-53 dBm	8.24 V
1732442212	103 Pkt	-54 dBm	8.24 V
1732440384	111 Pkt	-55 dBm	8.24 V
1732438553	110 Pkt	-56 dBm	8.24 V
1732436723	121 Pkt	-55 dBm	8.22 V
1732434892	104 Pkt	-55 dBm	8.24 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)