APRS Track Direct

My position About ☰

reset

9M2ZEW-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 9M2ZEW-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1732293099	1 Pkt	-54 dBm	8.96 V
1732291577	0 Pkt	-54 dBm	8.94 V
1732288850	1 Pkt	-55 dBm	8.96 V
1732287328	1 Pkt	-55 dBm	8.96 V
1732285806	1 Pkt	-54 dBm	8.96 V
1732284284	1 Pkt	-55 dBm	8.96 V
1732282762	1 Pkt	-56 dBm	8.96 V
1732281240	1 Pkt	-56 dBm	8.96 V
1732279718	1 Pkt	-54 dBm	8.98 V
1732278196	1 Pkt	-55 dBm	8.96 V
1732276674	1 Pkt	-54 dBm	8.96 V
1732275151	0 Pkt	-54 dBm	8.96 V
1732271994	1 Pkt	-54 dBm	8.96 V
1732270472	1 Pkt	-54 dBm	8.96 V
1732268950	1 Pkt	-53 dBm	8.96 V
1732267428	1 Pkt	-55 dBm	8.94 V
1732265906	1 Pkt	-53 dBm	8.96 V
1732264384	1 Pkt	-61 dBm	8.96 V
1732262862	1 Pkt	-53 dBm	8.96 V
1732261340	0 Pkt	-56 dBm	8.94 V
1732259817	2 Pkt	-57 dBm	8.96 V
1732258296	1 Pkt	-54 dBm	8.96 V
1732256773	1 Pkt	-53 dBm	8.96 V
1732255251	1 Pkt	-53 dBm	8.96 V
1732253729	1 Pkt	-53 dBm	8.96 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)