APRS Track Direct

My position About ☰

reset

VK5RPA-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK5RPA-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Eff1h*	Temp*
1744741992	13.73 Volt	0 Pcnt	23 C
1744740191	13.73 Volt	0 Pcnt	23.5 C
1744738389	13.73 Volt	100 Pcnt	24 C
1744736587	13.73 Volt	100 Pcnt	24.5 C
1744734785	13.73 Volt	100 Pcnt	24.5 C
1744732984	13.73 Volt	100 Pcnt	25 C
1744731182	13.73 Volt	100 Pcnt	25 C
1744729380	13.73 Volt	100 Pcnt	25 C
1744727578	13.73 Volt	100 Pcnt	25.5 C
1744725777	13.73 Volt	100 Pcnt	26.5 C
1744723975	13.73 Volt	100 Pcnt	27 C
1744722173	13.73 Volt	100 Pcnt	27.5 C
1744720371	13.73 Volt	100 Pcnt	27.5 C
1744718570	13.73 Volt	100 Pcnt	28 C
1744716768	13.73 Volt	100 Pcnt	28.5 C
1744714966	13.73 Volt	100 Pcnt	28.5 C
1744713164	13.73 Volt	100 Pcnt	29 C
1744711363	13.73 Volt	100 Pcnt	29.5 C
1744709561	13.73 Volt	100 Pcnt	30.5 C
1744707759	13.73 Volt	100 Pcnt	31 C
1744705958	13.65 Volt	100 Pcnt	31.5 C
1744704156	13.73 Volt	100 Pcnt	33 C
1744702354	13.8 Volt	100 Pcnt	34 C
1744700552	13.95 Volt	100 Pcnt	34.5 C
1744698751	13.88 Volt	100 Pcnt	35.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 1, 0

Dig1h: 0, 1, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -62

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)