APRS Track Direct

My position About ☰

reset

IR2BZ Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IR2BZ. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10m*	Rx1h*	Eff1h*
1790648396	93 Pkt	510 Pkt	67 Pcnt
1790648096	80 Pkt	490 Pkt	64 Pcnt
1790647795	81 Pkt	490 Pkt	64 Pcnt
1790647495	97 Pkt	480 Pkt	62 Pcnt
1790647195	97 Pkt	480 Pkt	60 Pcnt
1790646895	88 Pkt	450 Pkt	58 Pcnt
1790646594	96 Pkt	440 Pkt	56 Pcnt
1790646294	87 Pkt	420 Pkt	53 Pcnt
1790645994	71 Pkt	410 Pkt	52 Pcnt
1790645693	72 Pkt	410 Pkt	52 Pcnt
1790645393	69 Pkt	410 Pkt	52 Pcnt
1790645093	69 Pkt	400 Pkt	51 Pcnt
1790644792	75 Pkt	400 Pkt	50 Pcnt
1790644492	73 Pkt	400 Pkt	50 Pcnt
1790644192	70 Pkt	410 Pkt	50 Pcnt
1790643892	66 Pkt	400 Pkt	50 Pcnt
1790643591	57 Pkt	400 Pkt	49 Pcnt
1790643291	53 Pkt	410 Pkt	50 Pcnt
1790642991	76 Pkt	420 Pkt	51 Pcnt
1790642690	84 Pkt	430 Pkt	51 Pcnt
1790642390	67 Pkt	430 Pkt	50 Pcnt
1790642090	62 Pkt	430 Pkt	50 Pcnt
1790641790	55 Pkt	420 Pkt	48 Pcnt
1790641489	67 Pkt	440 Pkt	50 Pcnt
1790641189	82 Pkt	460 Pkt	50 Pcnt

*Used Equation Coefficients:

Rx10m: 0, 1, 0

Rx1h: 0, 10, 0

Dg10m: 0, 1, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)