APRS Track Direct

My position About ☰

reset

N1KAB-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N1KAB-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	V2*	Temp*	RFIn*	RFiGate*
1791931170	13.2 V	44 C	11 Pkts	11 Pkts
1791929370	13.8 V	44 C	4 Pkts	4 Pkts
1791927570	13.8 V	44 C	9 Pkts	9 Pkts
1791925771	14.9 V	43 C	9 Pkts	9 Pkts
1791923969	14 V	43 C	23 Pkts	21 Pkts
1791922169	13.4 V	44 C	21 Pkts	21 Pkts
1791920369	13.7 V	43 C	11 Pkts	11 Pkts
1791918569	13.4 V	43 C	6 Pkts	6 Pkts
1791916769	13.8 V	42 C	8 Pkts	8 Pkts
1791914970	14.8 V	42 C	5 Pkts	5 Pkts
1791913169	15.2 V	42 C	6 Pkts	6 Pkts
1791911370	13.5 V	42 C	7 Pkts	7 Pkts
1791909570	13.5 V	41 C	7 Pkts	7 Pkts
1791907769	14.3 V	41 C	6 Pkts	5 Pkts
1791905971	13.7 V	41 C	10 Pkts	10 Pkts
1791904170	13.4 V	41 C	13 Pkts	12 Pkts
1791902370	13.3 V	40 C	13 Pkts	12 Pkts
1791900569	13.1 V	40 C	11 Pkts	11 Pkts
1791898770	12.5 V	40 C	14 Pkts	13 Pkts
1791896969	12.4 V	40 C	37 Pkts	34 Pkts
1791895169	12.4 V	40 C	17 Pkts	15 Pkts
1791893369	12.4 V	40 C	18 Pkts	18 Pkts
1791891569	12.5 V	40 C	9 Pkts	9 Pkts
1791889769	12.5 V	40 C	11 Pkts	11 Pkts
1791887969	12.5 V	40 C	12 Pkts	12 Pkts

*Used Equation Coefficients:

V2: 0, 0.1, 0

Temp: 0, 1, 0

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)