APRS Track Direct

My position About ☰

reset

E29XZ-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E29XZ-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	TxTraffic*	GPS*	Voltage*
1786702349	0 Pkt	11 Sat	12.89 V
1786701755	4 Pkt	10 Sat	12.89 V
1786701160	1 Pkt	11 Sat	12.89 V
1786699377	3 Pkt	12 Sat	12.89 V
1786698783	2 Pkt	11 Sat	12.94 V
1786692839	2 Pkt	10 Sat	12.89 V
1786691056	0 Pkt	9 Sat	12.94 V
1786690461	1 Pkt	8 Sat	12.89 V
1786687489	2 Pkt	9 Sat	12.84 V
1786685112	4 Pkt	11 Sat	12.89 V
1786683923	1 Pkt	11 Sat	12.89 V
1786677979	4 Pkt	12 Sat	12.94 V
1786676790	1 Pkt	10 Sat	12.94 V
1786676196	1 Pkt	10 Sat	12.94 V
1786675602	0 Pkt	10 Sat	12.89 V
1786675007	1 Pkt	10 Sat	12.94 V
1786674413	4 Pkt	10 Sat	12.89 V
1786673819	1 Pkt	10 Sat	12.99 V
1786673224	0 Pkt	10 Sat	12.94 V
1786672035	1 Pkt	11 Sat	12.94 V
1786670847	4 Pkt	10 Sat	12.94 V
1786670252	0 Pkt	11 Sat	12.94 V
1786669658	1 Pkt	12 Sat	12.94 V
1786668469	1 Pkt	11 Sat	12.94 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

GPS: 0, 1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)