APRS Track Direct

My position About ☰

reset

TA2KZY-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA2KZY-7. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1836274299	0 Pkt	-31 dBm	0 V
1836274125	0 Pkt	-30 dBm	0 V
1774108402	0 Pkt	-30 dBm	0 V
1774107478	0 Pkt	-31 dBm	0 V
1774106554	0 Pkt	-30 dBm	0 V
1774105630	0 Pkt	-30 dBm	0 V
1774104706	0 Pkt	-32 dBm	0 V
1774103781	0 Pkt	-32 dBm	0 V
1774102857	5 Pkt	-31 dBm	0 V
1774101933	0 Pkt	-33 dBm	0 V
1774101009	0 Pkt	-31 dBm	0 V
1774100085	2 Pkt	-31 dBm	0 V
1774099160	0 Pkt	-30 dBm	0 V
1774098236	0 Pkt	-32 dBm	0 V
1774097312	0 Pkt	-32 dBm	0 V
1774096388	0 Pkt	-31 dBm	0 V
1774095464	1 Pkt	-31 dBm	0.02 V
1774094540	1 Pkt	-31 dBm	0 V
1774093616	4 Pkt	-31 dBm	0.02 V
1774092692	22 Pkt	-31 dBm	0 V
1774091767	1 Pkt	-29 dBm	0 V
1774090843	1 Pkt	-30 dBm	0 V
1774089918	1 Pkt	-30 dBm	0 V
1774088994	1 Pkt	-30 dBm	0.02 V
1774088070	2 Pkt	-30 dBm	0.02 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)