APRS Track Direct

My position About ☰

reset

LU2EP-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU2EP-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1732307822	11 Pkt	-55 dBm	11.87 V
1732305988	14 Pkt	-62 dBm	11.81 V
1732304154	21 Pkt	-62 dBm	11.46 V
1732302311	10 Pkt	-58 dBm	12.02 V
1732300480	10 Pkt	-58 dBm	11.94 V
1732298647	21 Pkt	-58 dBm	11.94 V
1732296804	12 Pkt	-58 dBm	11.48 V
1732294972	3 Pkt	-58 dBm	12.08 V
1732293146	10 Pkt	-55 dBm	11.67 V
1732291313	561 Pkt	-56 dBm	11.89 V
1732289043	58 Pkt	-58 dBm	11.92 V
1732286782	1351 Pkt	-54 dBm	11.57 V
1732283923	89 Pkt	-58 dBm	11.81 V
1732283660	974 Pkt	-58 dBm	11.89 V
1732281091	1116 Pkt	-58 dBm	11.96 V
1732277676	54 Pkt	-63 dBm	11.65 V
1732275108	1 Pkt	-53 dBm	11.81 V
1732273284	1 Pkt	-53 dBm	11.81 V
1732271459	0 Pkt	-53 dBm	12.43 V
1732269636	0 Pkt	-53 dBm	11.67 V
1732267812	0 Pkt	-52 dBm	11.96 V
1732265989	5 Pkt	-54 dBm	12.3 V
1732264161	0 Pkt	-52 dBm	12.2 V
1732262338	5 Pkt	-54 dBm	11.94 V
1732260511	2 Pkt	-53 dBm	12 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)