APRS Track Direct

My position About ☰

reset

TA7FTH-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA7FTH-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1732457083	27 Pkt	-60 dBm	3.83 V
1732456159	44 Pkt	-61 dBm	3.86 V
1732455235	76 Pkt	-61 dBm	3.86 V
1732454306	73 Pkt	-62 dBm	3.86 V
1732453377	44 Pkt	-63 dBm	3.86 V
1732452453	105 Pkt	-62 dBm	3.86 V
1732451523	122 Pkt	-63 dBm	3.86 V
1732450591	67 Pkt	-61 dBm	3.86 V
1732449665	82 Pkt	-61 dBm	3.86 V
1732448738	57 Pkt	-66 dBm	3.86 V
1732447811	41 Pkt	-62 dBm	3.83 V
1732446886	43 Pkt	-61 dBm	3.86 V
1732445959	42 Pkt	-60 dBm	3.86 V
1732445034	52 Pkt	-61 dBm	3.86 V
1732444108	29 Pkt	-61 dBm	3.83 V
1732443185	27 Pkt	-61 dBm	3.86 V
1732442262	28 Pkt	-62 dBm	3.86 V
1732441339	33 Pkt	-62 dBm	3.86 V
1732440414	21 Pkt	-61 dBm	3.86 V
1732439491	24 Pkt	-61 dBm	3.86 V
1732438568	25 Pkt	-60 dBm	3.86 V
1732437645	39 Pkt	-64 dBm	3.83 V
1732436721	48 Pkt	-70 dBm	3.83 V
1732435796	33 Pkt	-70 dBm	3.83 V
1732434871	89 Pkt	-70 dBm	3.83 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)