APRS Track Direct

My position About ☰

reset

TA7MZ-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA7MZ-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1790671381	8 Pkt	-83 dBm	0.62 V
1790670650	5 Pkt	-82 dBm	0.66 V
1790669920	5 Pkt	-83 dBm	0.64 V
1790669191	7 Pkt	-81 dBm	0.66 V
1790668462	6 Pkt	-81 dBm	0.66 V
1790667731	6 Pkt	-84 dBm	0.62 V
1790667001	7 Pkt	-84 dBm	0.64 V
1790666271	7 Pkt	-85 dBm	0.66 V
1790665541	9 Pkt	-85 dBm	1.03 V
1790664811	6 Pkt	-78 dBm	0.66 V
1790664080	5 Pkt	-78 dBm	0.66 V
1790663350	10 Pkt	-79 dBm	0.66 V
1790662621	9 Pkt	-78 dBm	0.66 V
1790661890	10 Pkt	-82 dBm	0.62 V
1790661160	6 Pkt	-78 dBm	0.64 V
1790660430	3 Pkt	-77 dBm	0.62 V
1790659700	7 Pkt	-78 dBm	0.62 V
1790658970	11 Pkt	-82 dBm	0.68 V
1790658240	1 Pkt	-82 dBm	0.62 V
1790657510	2 Pkt	-82 dBm	0.66 V
1790656780	0 Pkt	-82 dBm	0.64 V
1790655977	2 Pkt	-77 dBm	0.66 V
1790655247	2 Pkt	-79 dBm	0.66 V
1790654517	1 Pkt	-82 dBm	0.64 V
1790653787	2 Pkt	-82 dBm	0.74 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)