APRS Track Direct

My position About ☰

reset

W9BED-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W9BED-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	DigiRpt*	Temp*
1786721106	100 Pkts	96 Pkts	69 Pkts	15 C
1786717506	93 Pkts	92 Pkts	54 Pkts	14 C
1786713907	162 Pkts	161 Pkts	62 Pkts	14 C
1786710307	207 Pkts	206 Pkts	38 Pkts	14 C
1786706706	107 Pkts	107 Pkts	42 Pkts	14 C
1786703106	110 Pkts	108 Pkts	41 Pkts	14 C
1786699506	79 Pkts	78 Pkts	37 Pkts	14 C
1786695906	102 Pkts	96 Pkts	39 Pkts	14 C
1786692306	167 Pkts	161 Pkts	53 Pkts	15 C
1786688706	127 Pkts	123 Pkts	48 Pkts	15 C
1786685106	121 Pkts	113 Pkts	50 Pkts	15 C
1786681506	140 Pkts	131 Pkts	51 Pkts	15 C
1786677906	89 Pkts	88 Pkts	41 Pkts	16 C
1786674306	104 Pkts	101 Pkts	46 Pkts	16 C
1786670706	129 Pkts	127 Pkts	82 Pkts	16 C
1786667106	98 Pkts	96 Pkts	70 Pkts	16 C
1786663506	92 Pkts	89 Pkts	55 Pkts	16 C
1786659906	114 Pkts	112 Pkts	73 Pkts	17 C
1786656307	33 Pkts	33 Pkts	22 Pkts	19 C
1786652706	0 Pkts	0 Pkts	0 Pkts	19 C
1786649106	0 Pkts	0 Pkts	0 Pkts	19 C
1786645506	36 Pkts	36 Pkts	21 Pkts	17 C
1786641906	20 Pkts	19 Pkts	17 Pkts	17 C
1786638306	60 Pkts	57 Pkts	33 Pkts	15 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)