APRS Track Direct

My position About ☰

reset

YM2KV-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YM2KV-5. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1786733677	13 Pkt	-40 dBm	12.45 V
1786733050	25 Pkt	-41 dBm	12.45 V
1786732420	16 Pkt	-41 dBm	12.45 V
1786731793	21 Pkt	-41 dBm	12.45 V
1786731166	4 Pkt	-39 dBm	12.45 V
1786730593	17 Pkt	-40 dBm	12.45 V
1786729964	18 Pkt	-40 dBm	12.45 V
1786729337	19 Pkt	-38 dBm	12.45 V
1786728707	20 Pkt	-38 dBm	12.45 V
1786728080	21 Pkt	-40 dBm	12.45 V
1786727454	18 Pkt	-40 dBm	12.45 V
1786726828	22 Pkt	-38 dBm	12.45 V
1786726199	27 Pkt	-39 dBm	12.45 V
1786725569	19 Pkt	-41 dBm	12.45 V
1786724942	20 Pkt	-40 dBm	12.45 V
1786724314	18 Pkt	-40 dBm	12.45 V
1786723686	35 Pkt	-41 dBm	12.45 V
1786723054	17 Pkt	-40 dBm	12.45 V
1786722427	15 Pkt	-40 dBm	12.45 V
1786721801	17 Pkt	-40 dBm	12.47 V
1786721176	18 Pkt	-40 dBm	12.45 V
1786720549	17 Pkt	-41 dBm	12.45 V
1786719921	15 Pkt	-41 dBm	12.45 V
1786719295	13 Pkt	-42 dBm	12.45 V
1786718668	13 Pkt	-39 dBm	12.45 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)