APRS Track Direct

My position About ☰

reset

VK6KCH-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK6KCH-7. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Latency*	PktLoss*	RackTemp*
1790640330	88 ms	0 percent	13.15 degC
1790640030	96 ms	0 percent	12.88 degC
1790639730	80 ms	0 percent	12.88 degC
1790639431	76 ms	0 percent	12.6 degC
1790639131	92 ms	0 percent	12.6 degC
1790638831	96 ms	0 percent	12.33 degC
1790638231	84 ms	0 percent	12.33 degC
1790637931	108 ms	0 percent	12.33 degC
1790637632	96 ms	0 percent	12.05 degC
1790637032	88 ms	0 percent	12.05 degC
1790636731	88 ms	0 percent	11.78 degC
1790636129	88 ms	0 percent	11.78 degC
1790635530	84 ms	0 percent	11.5 degC
1790635231	108 ms	0 percent	11.23 degC
1790634932	80 ms	0 percent	11.23 degC
1790634631	80 ms	0 percent	11.23 degC
1790634331	80 ms	0 percent	11.23 degC
1790633731	88 ms	0 percent	11.23 degC
1790633430	88 ms	0 percent	11.23 degC
1790633131	96 ms	0 percent	11.23 degC
1790632829	128 ms	0 percent	11.23 degC
1790632530	92 ms	0 percent	11.23 degC
1790632229	84 ms	0 percent	11.23 degC
1790631930	80 ms	0 percent	11.23 degC
1790631631	104 ms	0 percent	11.23 degC

*Used Equation Coefficients:

Latency: 0, 4, 0

PktLoss: 0, 1, 0

RackTemp: 0, 0.275, -5

Res4: 0, 1, 0

Res5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)