APRS Track Direct

My position About ☰

reset

DA0WW-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DA0WW-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Batt12V*	Batt48V*	Umin*	Cell#*
1790657268	12.9 V	48 V	203 V	17 #
1790653650	12.9 V	48 V	203 V	17 #
1790646412	12.9 V	48 V	203 V	17 #
1790644601	12.9 V	48 V	203 V	17 #
1790642793	12.9 V	48 V	203 V	17 #
1790639174	12.9 V	48 V	203 V	17 #
1790637365	12.9 V	48 V	203 V	17 #
1790635555	12.9 V	48 V	203 V	17 #
1790633745	12.9 V	48 V	203 V	17 #
1790631936	12.9 V	48 V	203 V	17 #
1790630125	12.9 V	48 V	203 V	17 #
1790626507	12.9 V	48 V	203 V	17 #
1790624700	12.9 V	48 V	203 V	17 #
1790622888	12.9 V	48 V	203 V	17 #
1790621080	12.9 V	48 V	203 V	17 #
1790619270	12.9 V	48 V	203 V	17 #
1790617465	12.9 V	48 V	203 V	17 #
1790615651	12.9 V	48 V	203 V	17 #
1790613843	12.9 V	48 V	203 V	17 #
1790610225	12.9 V	48 V	203 V	17 #
1790608415	12.9 V	48 V	203 V	17 #
1790606606	12.9 V	48 V	203 V	17 #
1790602989	12.9 V	48 V	203 V	17 #
1790593937	12.9 V	48 V	203 V	17 #
1790592132	12.9 V	48 V	203 V	17 #

*Used Equation Coefficients:

Batt12V: 0, 0.1, 0

Batt48V: 0, 0.2, 0

I48V: 0, 1, 0

Umin: 0, 1, 0

Cell#: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)