APRS Track Direct

My position About ☰

reset

E24BD-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E24BD-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1786740321	5 Pkt	-44 dBm	5.62 V
1786739397	6 Pkt	-44 dBm	5.6 V
1786738473	6 Pkt	-44 dBm	5.6 V
1786737548	4 Pkt	-45 dBm	5.6 V
1786736624	6 Pkt	-46 dBm	5.62 V
1786735699	5 Pkt	-46 dBm	5.6 V
1786734775	4 Pkt	-45 dBm	5.6 V
1786733851	8 Pkt	-45 dBm	5.62 V
1786732926	5 Pkt	-47 dBm	5.6 V
1786732001	3 Pkt	-44 dBm	5.6 V
1786731077	5 Pkt	-43 dBm	5.76 V
1786730153	4 Pkt	-45 dBm	5.6 V
1786729228	7 Pkt	-45 dBm	5.6 V
1786728303	3 Pkt	-46 dBm	5.6 V
1786727378	2 Pkt	-45 dBm	5.6 V
1786726454	6 Pkt	-46 dBm	5.6 V
1786725530	4 Pkt	-45 dBm	5.62 V
1786724605	8 Pkt	-46 dBm	5.6 V
1786723681	6 Pkt	-45 dBm	5.6 V
1786722756	5 Pkt	-46 dBm	5.6 V
1786721832	5 Pkt	-45 dBm	5.6 V
1786720908	6 Pkt	-46 dBm	5.76 V
1786719983	9 Pkt	-44 dBm	5.6 V
1786719059	6 Pkt	-45 dBm	5.6 V
1786718134	6 Pkt	-45 dBm	5.62 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)