APRS Track Direct

My position About ☰

reset

YD3DCY-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YD3DCY-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	RxTraffic*	RSSI*	Voltage*
1732267680	8 Pkt	-40 dBm	0.86 V
1732266753	17 Pkt	-41 dBm	1.64 V
1732265826	13 Pkt	-40 dBm	2.5 V
1732264899	13 Pkt	-40 dBm	4.63 V
1732263971	8 Pkt	-40 dBm	5.62 V
1732263045	10 Pkt	-40 dBm	6.11 V
1732262118	2 Pkt	-41 dBm	5.35 V
1732261191	0 Pkt	-39 dBm	5.19 V
1732260264	0 Pkt	-41 dBm	6.58 V
1732259337	1 Pkt	-39 dBm	11.89 V
1732258411	0 Pkt	-41 dBm	13.64 V
1732257484	0 Pkt	-40 dBm	12.63 V
1732256492	0 Pkt	-40 dBm	12.22 V
1732255565	0 Pkt	-41 dBm	11.71 V
1732254638	0 Pkt	-42 dBm	13.82 V
1732253712	0 Pkt	-41 dBm	15.46 V
1732252784	0 Pkt	-39 dBm	16.82 V
1732251859	0 Pkt	-40 dBm	15.18 V
1732250930	0 Pkt	-40 dBm	15.71 V
1732250004	0 Pkt	-40 dBm	14.27 V
1732249076	0 Pkt	-40 dBm	15.07 V
1732248149	0 Pkt	-40 dBm	15.75 V
1732247223	0 Pkt	-41 dBm	15.52 V
1732246296	0 Pkt	-42 dBm	15.57 V
1732245369	0 Pkt	-41 dBm	16.43 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)