APRS Track Direct

My position About ☰

reset

TA3TX-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA3TX-12. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	RxTraffic*	RxDrop*	RSSI*	Voltage*
1732461234	1 Pkt	2 Pkt	-73 dBm	21 V
1732460851	1 Pkt	0 Pkt	-75 dBm	21 V
1732460468	1 Pkt	2 Pkt	-74 dBm	21 V
1732460086	6 Pkt	0 Pkt	-76 dBm	21 V
1732459701	0 Pkt	0 Pkt	-75 dBm	21 V
1732459319	0 Pkt	0 Pkt	-76 dBm	21 V
1732458937	0 Pkt	0 Pkt	-76 dBm	21 V
1732458554	7 Pkt	1 Pkt	-75 dBm	21 V
1732458170	12 Pkt	0 Pkt	-76 dBm	21 V
1732457787	4 Pkt	2 Pkt	-76 dBm	21 V
1732457404	1 Pkt	0 Pkt	-73 dBm	21 V
1732457022	4 Pkt	2 Pkt	-75 dBm	21 V
1732456638	7 Pkt	0 Pkt	-74 dBm	21 V
1732456253	11 Pkt	0 Pkt	-76 dBm	21 V
1732455869	12 Pkt	1 Pkt	-73 dBm	21 V
1732455481	8 Pkt	1 Pkt	-73 dBm	21 V
1732455096	8 Pkt	3 Pkt	-74 dBm	21 V
1732454710	8 Pkt	1 Pkt	-74 dBm	21 V
1732454323	8 Pkt	0 Pkt	-74 dBm	21 V
1732453936	5 Pkt	1 Pkt	-73 dBm	21 V
1732453553	1 Pkt	0 Pkt	-74 dBm	21 V
1732453170	2 Pkt	0 Pkt	-74 dBm	21 V
1732452787	5 Pkt	1 Pkt	-73 dBm	21 V
1732452404	3 Pkt	1 Pkt	-71 dBm	21 V
1732452021	4 Pkt	2 Pkt	-72 dBm	21 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)