APRS Track Direct

My position About ☰

reset

LU9OZX-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU9OZX-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1786802923	8 Pkt	-32 dBm	15.05 V
1786802253	23 Pkt	-34 dBm	15.36 V
1786801330	11 Pkt	-31 dBm	15.75 V
1786800407	31 Pkt	-31 dBm	15.28 V
1786799479	24 Pkt	-31 dBm	15.03 V
1786798554	0 Pkt	-33 dBm	15.69 V
1786797945	26 Pkt	-30 dBm	16.78 V
1786797019	7 Pkt	-31 dBm	16.75 V
1786796097	7 Pkt	-30 dBm	16.65 V
1786795174	5 Pkt	-29 dBm	16.86 V
1786794252	2 Pkt	-30 dBm	16.84 V
1786793330	6 Pkt	-28 dBm	17.04 V
1786792408	4 Pkt	-29 dBm	16.45 V
1786791485	7 Pkt	-29 dBm	16.3 V
1786790563	1 Pkt	-30 dBm	16.59 V
1786789641	2 Pkt	-28 dBm	16.61 V
1786788718	12 Pkt	-30 dBm	16.43 V
1786787795	0 Pkt	-29 dBm	16.75 V
1786786890	776 Pkt	-33 dBm	16.63 V
1786785918	1088 Pkt	-33 dBm	16.32 V
1786784929	1094 Pkt	-32 dBm	15.96 V
1786783940	707 Pkt	-32 dBm	16.73 V
1786782968	34 Pkt	-34 dBm	16.49 V
1786782482	162 Pkt	-29 dBm	16.88 V
1786781459	82 Pkt	-30 dBm	16.61 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)