APRS Track Direct

My position About ☰

reset

SR0L Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR0L. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Value1*	Value2*	Value3*	Value4*
1732294052	249 Raw	25 Raw	23.75 DegC	13.2 V
1732291537	250 Raw	25 Raw	23.75 DegC	13.2 V
1732290908	250 Raw	25 Raw	23.75 DegC	13.12 V
1732290279	251 Raw	25 Raw	23.75 DegC	13.2 V
1732289650	249 Raw	25 Raw	23.75 DegC	13.2 V
1732288396	252 Raw	25 Raw	23.75 DegC	13.16 V
1732287771	4 Raw	26 Raw	23.75 DegC	13.22 V
1732287142	9 Raw	26 Raw	23.75 DegC	13.2 V
1732283993	15 Raw	26 Raw	23.75 DegC	13.18 V
1732283365	13 Raw	26 Raw	23.75 DegC	13.16 V
1732281480	17 Raw	26 Raw	23.75 DegC	13.16 V
1732278965	19 Raw	26 Raw	23.75 DegC	13.12 V
1732277706	24 Raw	26 Raw	23.75 DegC	13.2 V
1732277078	24 Raw	26 Raw	23.75 DegC	13.2 V
1732276448	28 Raw	26 Raw	23.75 DegC	13.18 V
1732275191	38 Raw	26 Raw	23.75 DegC	13.16 V
1732273926	43 Raw	26 Raw	23.75 DegC	13.16 V
1732273295	42 Raw	26 Raw	23.75 DegC	13.22 V
1732272037	49 Raw	26 Raw	23.75 DegC	13.2 V
1732270779	59 Raw	26 Raw	23.75 DegC	13.14 V
1732267631	74 Raw	26 Raw	23.75 DegC	13.2 V
1732267002	76 Raw	26 Raw	23.75 DegC	13.2 V
1732264481	91 Raw	26 Raw	23.75 DegC	13.18 V
1732263853	95 Raw	26 Raw	23.75 DegC	13.22 V
1732261965	103 Raw	26 Raw	23.75 DegC	13.2 V

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 0.25, -40

Value4: 0, 0.02, 10

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)