APRS Track Direct

My position About ☰

reset

BM3FFG-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM3FFG-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1790672913	42.2 C	0 p	0 p	2266 p
1790671713	45.5 C	0 p	6 p	2266 p
1790670514	44 C	0 p	8 p	2266 p
1790669313	44.8 C	6 p	8 p	2266 p
1790668113	44 C	2 p	2 p	2260 p
1790666913	45.1 C	0 p	0 p	2258 p
1790665713	44 C	0 p	0 p	2258 p
1790664514	43.4 C	0 p	0 p	2258 p
1790663313	42.5 C	0 p	0 p	2258 p
1790662113	43.2 C	0 p	0 p	2258 p
1790660913	43.1 C	0 p	0 p	2258 p
1790659713	42.6 C	0 p	0 p	2258 p
1790658514	44 C	0 p	0 p	2258 p
1790657313	41.5 C	0 p	0 p	2258 p
1790656113	43 C	0 p	0 p	2258 p
1790654914	43.1 C	0 p	3 p	2258 p
1790653713	40.8 C	0 p	7 p	2258 p
1790652513	40 C	3 p	15 p	2259 p
1790651313	40.7 C	4 p	37 p	2269 p
1790650113	40.2 C	8 p	58 p	2273 p
1790648914	39.9 C	25 p	75 p	2293 p
1790647713	38.9 C	25 p	68 p	2289 p
1790646513	38 C	25 p	65 p	2284 p
1790645313	38.4 C	18 p	67 p	2276 p
1790644113	36.2 C	22 p	88 p	2261 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)