APRS Track Direct

My position About ☰

reset

BU2GE-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BU2GE-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1749321905	40.1 C	0 p	0 p	2546 p
1749320705	39 C	0 p	0 p	2569 p
1749319505	39.7 C	0 p	0 p	2599 p
1749318305	38.4 C	0 p	0 p	2629 p
1749317106	39.5 C	0 p	0 p	2657 p
1749315906	38.3 C	0 p	0 p	2682 p
1749314706	38.5 C	0 p	0 p	2715 p
1749313506	39.4 C	0 p	0 p	2744 p
1749312306	39.1 C	0 p	0 p	2768 p
1749311105	39.1 C	0 p	0 p	2801 p
1749309905	39.1 C	0 p	0 p	2823 p
1749308705	39.5 C	0 p	32 p	2853 p
1749307505	38.8 C	0 p	64 p	2891 p
1749306305	38.5 C	32 p	90 p	2918 p
1749305105	38.6 C	32 p	127 p	2938 p
1749303905	38.8 C	26 p	140 p	2961 p
1749302706	40.6 C	69 p	152 p	2975 p
1749301506	40.2 C	45 p	107 p	2933 p
1749300306	39 C	38 p	81 p	2939 p
1749299106	39.5 C	24 p	62 p	2923 p
1749297905	39.5 C	19 p	61 p	2919 p
1749296705	39.1 C	19 p	89 p	2973 p
1749295505	39.4 C	23 p	96 p	2982 p
1749294305	39.1 C	47 p	107 p	2991 p
1749293105	40 C	26 p	104 p	2987 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)